Mobotix presenta la nuova telecamera IP-Dome Q24, che sostituisce e migliora la rivoluzionaria Q22.
In particolare la Q24 si presenta esteticamente identica alla Q22, ma monta un nuovo e più potente processore, che permette di raggiungere i 30 fps in formato MEGA contro i 14 fps della Q22 e utilizza il formato microSD per la memoria interna, con una scheda da 4 Gb già inclusa e possibilità di espansione fino a 32 Gb.

La telecamera IP-Dome ultracompatta MOBOTIX è resistente agli agenti atmosferici e ha un'estetica discreta tanto da non essere notata. Grazie alla sua vista completa a 360° può controllare e registrare, tramite gestione di eventi, le immagini di un'intera stanza.

 

Principali caratteristiche:

• Hemisferic per una visualizzazione completa e una copertura totale di una stanza
• Zoom e brandeggio digitale in modalità continua
• Robusta e senza parti mobili, non necessita di nessuna manutenzione
• Riprese di un'intera stanza e registrazione in base agli eventi direttamente sulla telecamera (4GB scheda microSD incl.)
• Funzioni d'allarme, microfono e altoparlante integrati
• Insospettabile ed esteticamente discreta

 

 

DOWNLOAD

Scarica la brochure in formato .PDF:
  mx_PF_Q24_en_090602.pdf (375.39 Kb)

Scarica la scheda tecnica in formato .PDF:
  mx_TS_q24sec_en_090615.pdf (544.77 Kb)

Scarica il manuale in formato .PDF:
  

 

 

Modelli	Basic, Sec
Lenti	L11 (hemispherical) L22 (90° x 67°)
Sensibilità	Colore: 1 lux (t=1/60 s), 0,05 lux (t=1/1 s)
Sensore	1/2“ CMOS, scansione progressiva
Risoluzione Immagine	Colore: 2048 x 1536 (3 MEGA)
Formati Immagine	2048 x 1536, 1280 x 960, 1024 x 768, 800 x 600, 768 x 576 (D1), 704 x 576 (TV-PAL), 640 x 480, 384 x 288, 352 x 288, 320 x 240, 160 x 120; creazione formati personalizzati (e.g. 1000 x 200)
Frame Rate (M-JPEG) (Live/Registrazione)	VGA: 16 fps, TV-PAL: 12 fps, MEGA: 6 fps, 3MEGA: 4 fps
Video Stream (MxPEG) (Live/Registrazione/Audio)	VGA: 30 fps, TV-PAL: 24 fps, MEGA: 14 fps, 3MEGA: 10 fps
Compressione Immagine	MxPEG, M-JPEG, JPG, H.263 (Video-Telefonia-VoIP)
DVR interno	Slot per scheda SD (fino a 16 GB)
Storage esterno	Direttamente su NAS o PC/Server senza utilizzaresoftware di registrazione
Software (incluso)	Software di Gestione Video MxEasy, software per sala controllo MxControlCenter
Elaborazione Immagine	Correzione controluce, bilanciamento del bianco, correzione aberrazione ottica, sensore di movimento
PTZ virtuale	Pan/Tilt/Zoom digitale, 8x zoom continuo
Allarmi/Eventi	Acquisizione eventi tramite finestre multiple di motion detection integrato, segnali esterni, sensore temperatura, notifiche via email, FTP, telefonia IP (VoIP, SIP), allarmi visuali/acustici Immagini pre- e post- allarme
Audio	Microfono e altoparlante integrati, audio sincronizzato labbiale, bidirezionale, registrazione audio
Interfaccie	Ethernet 10/100
Audio/Telefonia	VoIP, SIP, conversazione bidirezionale, controllo remotoconnessioni in-out della telecamera, notifica eventi
Sicurezza	Gestione Utenti/Gruppi, HTTPS/SSL, filtro indirizzi IP, IEEE 802.1x, Intrusion Detection
Certificazioni	BGV C9 (“UVV”), EMV (applicazioni civili, industriali), EN 50155 (shock, vibrazione, temperatura), CE, FCC
Alimentazione	Alimentazione tramite Ethernet (IEE 802.3af; Class 0), Trasformatore opzionale, tipico 4 W
Condizioni Operative	IP65 ( DIN EN 60529), da -30° a +60° C (da -22°F a +140°F)
Dimensioni	Ø x H: 16 x 5 cm, Peso: ca. 450 g
Consegna standard	Alloggiamento in plastica ad alta resistenza (PBT-PC), bianco, lens protection (transparent polycarbonate), incl. 360° lenti, kit di montaggio, brugola, cavo patch S/FTP yellow 8-wire 50 cm (double-shielded), manuale, software

 

 

	Power adapter set for power supply via the network - Power supply over PoE - For all camera models (Mx30V) Prezzo: € 98,00
	Rack di alimentazione di rete NETPOWER per 4 videocamere (30 V) Prezzo: € 398,00
	Vandalism Housing for Q24 - Vandalism-proof stainless steel housing including lens protection - Ideally suited for surveillance at extremely critical locations Prezzo: attualmente non disponibile
	In-Ceiling Set for D22 and Q22/Q24 - Consists of in-ceiling mount and mounting parts - Easy mounting from front - Installation dimension: ∅ 150 mm Prezzo: Euro 98,00 + Iva
	ExtIO Extension Module - Microphone/speaker - PIR sensor for motion detection, temperature sensor - Integrated switch functions Prezzo: Euro 198,00 + Iva

Mounting Options

Mounting to a Ceiling or Wall

The MOBOTIX Q22M has been primarily designed to be mounted to either ceilings or walls (in combination with the Wall Mount).
The supplied L11 180° lens then allows monitoring the entire room from the bottom to the ceiling.
The Q22M can also be mounted directly to a wall without using the wall mount. The cable entry of the Q22M is below the center of the camera's back plate. 

 

Installation Options

On-wall mounting The On-Wall set can reliably protect external cables if the cables cannot be guided from below the housing but have to be led above the wall. In addition, the On-Wall mount provides ample space for extra modules.
On-wall mounting with 10° incline This On-Wall set is identical to the regular On-Wall set, except that the mounted camera is inclined by 10 degrees. The incline makes it possible for the camera to deliver the best images even in demanding situations.
In-ceiling mounting The In-Ceiling set allows mounting the Q22M cameras in fake ceilings, for example. This type of installation provides optimum protection for the camera and reduces the visible profile to a minimum since the camera only protrudes 24 mm (1 in) from the ceiling.
Vandalism protection The Vandalism set provides added protection for Q22M cameras. The set consists of a robust stainless steel cover and a dome made of polycarbonate. A camera equipped with the Vandalism set is perfectly suited for applications in demanding environments (such as prisons, social hot spots, train stations, etc.).
Wall Mount The Q22M/D22M Wall Mount is the ideal solution for mounting the Q22M to walls for indoor and outdoor applications. The camera is absolutely dustproof and resistan against water jets (IP65). The wall mount also covers RJ45 wall outlets and has ample space for additional modules.
Pole Mount If you would like to mount the MOBOTIX Q22M to a pole, you should consider using the MOBOTIX Pole Mount. This mount can only be used in conjunction with the wall mount. The supplied stainless steel straps allow attaching the mount to poles with diameters between 60 and 180 mm (2.4 to 7.1 in).

Mounting Types Q22

The MOBOTIX Q22M consists of the camera housing (motherboard and lens), the outer shell and the mounting ring.

On-Wall Set

 

In-Ceiling Set
 

Vandalism Set
 

 

 

Mounting Instructions

Outdoor Wall Mount

The Q22M/D22M Wall Mount is the ideal solution for mounting the Q22M to walls for outdoor applications.The camera is absolutely weatherproof (IP65). The wall mount has ample space for additional modules (UMTS, WLAN etc.).

The Wall Mount also covers RJ45 wall outlets and also has ample space for additional modules.

 

Pole Mount

If you would like to mount the MOBOTIX Q22M to a pole, you should consider using the MOBOTIX Pole Mount. This mount can only be used in conjunction with the wall mount. The supplied stainless steel straps allow attaching the mount to poles with diameters between 60 and 180 mm.

The Pole Mount is made from 3 mm white powdercoated stainless steel and is just as robust and maintenance-free as the outdoor Wall Mount

 

 

Hints for Choosing a Good Mounting Position

In order to get the most out of the MOBOTIX Q22M, you should follow these mounting hints.

360° Allround View Thanks to its hemispherical lens, a single Q22M can monitor an entire room right into each of the four corners (360° Allround Surveillance). The camera's ideal position is on the ceiling in the center of the room. Due to its inherent physical and optical properties, the precision of the lens decreases as the distance from the lens grows. This means that the maximum usable image area greatly varies with the purpose of the camera. Rooms with a square floor area of up to approx. 40 m² (48 yd²) in general allow recognizing details even at the borders of the full image. If you would only like to know if persons enter a room or for monitoring specific objects, rooms with up to 100 m² (120 yd²) floor area can be monitored using a single Q22M.
Facial Recognition If the camera is used to detect persons and recognize their faces, the camera should be mounted at heights between 2.8 and 3 m (9.2 to 9.8 ft). Facial recognition up to 1.5 m (5 ft) distance to the object is very good and up to 3 m (9.8 ft) is still sufficient. Persons that are already known can be properly identified up to 5 m (16.4 ft) distance from the camera.
Non-Square Rooms When viewing a 360° (full) image in the browser, you will notice that the top and bottom of the image is not fully visible, i.e. some image information has been clipped. This is not a fault of the camera, but an intended behavior that aims at achieving the best possible utilization of the image sensor by the camera software. Bearing this in mind, it is advisable to install a Q22M in rectangular rooms so that the arrow marked as OBEN /TOP points towards one of the long sides of the room as shown in the figure.
Lowered Mounting or Mounting on Extensions When mounting the camera in rooms with a high ceiling, it may be advisable tomount the camera in a lower position. This reduces the distance between the camera and the objects that are to be monitored, which in turn increases the recognizability of details. One practical solution would be to install the camera on a base plate attached to a suitable extension (metal tube) that is hanging from the ceiling. The network cable can be hidden from view by running through the interior of the tube. Similar to such a lowered mounting from the ceiling, you can also attach the camera to an extension mounted to a wall to better use the 360° image of the camera (e.g. outside, above a portal). Such an installation would use the pole mount accessory (MX-D22-OPT-MH) in conjunction with the wall mount (MX-D22-OPT-WH) as a sturdy camera carrier, which is then mounted to the extension pole. MOBOTIX recommends not to attach the camera directly to metal carriers, especially when mounting the camera outdoors or when the ambient temperature varies greatly. As an additional measure to protect the camera against condensation, you should use either the On-Wall set (MX-D22-OPT-AP) or the Wall Mount (MX-D22-OPT-WH).

Connecting the Camera

The MOBOTIX camera does not require any software installation; all you need is your preferred browser with JavaScript support to operate the camera. Thus, the MOBOTIX camera is supported by all common operating systems (such as Windows, Macintosh and Linux, ...).

If the camera is supplied with Power over Ethernet (a PoE switch), then no other device will be necessary for supplying power.

Establishing the Power Supply to the Camera

You can choose between the following options:

1. External power supply and Network Power Adapter (MX-NPA-3-RJ): Power supply of one camera injected into the network cabling (max. length 100 m (110 yd)), from the NPA to the 10BaseT/NET connector of the camera
2. Network Power Box/Rack (MX-NPR-4, or 8/20): Power supply of 4/8/20 cameras injected into the network cabling (max. length 100 m (110 yd)), from the NPR to the 10BaseT/NET connector of the camera
3. Power over Ethernet: Power supply using network components that are conforming to the PoE standard IEEE 802.3af

Power Supply (MxPoE) Using a Switch

1. Connect the factory pre-installed cable of the camera to the Camera connector of the Network Power Adapter.
2. Connect the LAN/Power connector of the NPA to an Ethernet connector of the switch/router or the Ethernet wall outlet.
3. Plug the RJ45 connector of the external power unit into the PC/Power connector of the Network Power Adapter.

 

 

Power Supply (MxPoE) When Connected Directly to a Computer

1. Connect the factory pre-installed cable of the camera to the Camera connector of the Network Power Adapter.
2. Connect the PC/Power connector of the Network Power Adapter to the Ethernet port of the computer.
3. Plug the RJ45 connector of the external power unit into the LAN/Power connector of the Network Power Adapter.

 

 

Power Supply (MxPoE) Using a Network Power Rack or Network Power Box

1. Connect the factory pre-installed cable of the camera to the CAM connector of the Network Power Rack (MX-NPR-8/20) or the Network Power Box  (MX-NPR-4).
2. Connect the LAN connector of the Network Power Rack to an Ethernet connector of the switch/router.

 

 

Power Supply (PoE IEEE 802.3af) Using Power-over-Ethernet Products

1. Connect the factory pre-installed cable of the camera to the Ethernet connector of the PoE switch/router.
2. The switch/router needs to support the PoE standard IEEE 802.3af.

 

	Q24M Basic	Q24M Sec
Interno/Esterno:	Interno (IP54), -30°...+50°C	Interno/Esterno, resistente alle intemperie (IP65), -30°..+60°C
Lenti: (eq. 35mm)	Emisferica (11mm,360°,F2.0) Super Grandangolare (22mm,90°,F2.0)	Emisferica (11mm,360°,F2.0) Super Grandangolare (22mm, 90°,F2.0)
Risoluzione:	VGA (640x480 pixels), colore	3MEGA (2048x1536 pixels)
Pan/Tilt/Zoom:	PTZ digitale via MxControlCenter	PTZ digitale, 8x Zoom continuo
Frame Rate (Mono):	16 fps VGA • 16 fps CIF	30 fps VGA • 10 fps MEGA 4 fps 3MEGA
Sensibilità:	1 lux (t=1/60s) • 0,05 lux (t=1/1s)	1 lux (t=1/60s) • 0,05 lux (t=1/1s)
Interfaccie:	Ethernet 10/100 Mbps	Ethernet 10/100 Mbps, USB, audio esterno
DVR interno:	./.	Fino a 16 GB su SD-card
Audio/Telefonia:	./.	Bidirezionale, telefonia IP (VoIP)
Alimentazione • Ent./Usc.	PoE o MX30V • ./.	PoE o MX-NPA-Set • via ExtIO
Caratteristiche Software:	Correzione aberrazione ottica in MxCC, FTP, E-Mail, gestione video allarmi, Multiview	Correzione aberrazione ottica in MxCC, FTP, E-Mail, gestione video allarmi, Multiview
Progr. eventi • Triggering:	./.	365 giorni pianificabili • eventi multipli
Memoria esterna:	./.	Fino a 1 TB su PC/Server/NAS

 

	Obiettivo L11	Obiettivo L22
Immagine originale:
Lunghezza focale equivalente 35mm	11 mm	22 mm
Lunghezza focale	1.8 mm	4 mm
Apertura	2.0	2.0
Angolo orizzontale	180°	90°
Angolo verticale	160°	67°
Distanza 1 m	m	m
• Larghezza immagine	infinitely	2.0
• Altezza immagine	11	1.3
Distanza 5 m	m	m
• Larghezza immagine	infinitely	10.0
• Altezza immagine	55	6.6
Distanza 10 m	m	m
• Larghezza immagine	infinitely	20.0
• Altezza immagine	110	13,3
Distanza20 m	m	m
• Larghezza immagine	infinitely	40.0
• Altezza immagine	220	26.6
Distanza 50 m	m	m
• Larghezza immagine	infinitely	100.0
• Altezza immagine	550	66.0

Note

Le lunghezze focali indicate per gli obiettivi MOBOTIX non corrispondono al valore effettivo, ma alla lunghezza focale (Lxx mm) convertita in formato 35 mm. Ad esempio l’obiettivo supergrandangolo MOBOTIX L22 ha una lunghezza focale effettiva di 4 mm, l’equivalente in formato 35 mm è di 22 mm. Per questa ragione viene definito L22. 

Dato che i sensori di immagine delle telecamere digitali hanno dimensioni diverse, la conversione in formato 35mm consente un confronto più semplice dei formati di immagine e del campo di ripresa delle diverse lenti. Un altro vantaggio è che si può impostare una telecamera 35mm (analogica o digitale) con la stessa lunghezza focale (Lxx) per otterene lo stesso campo di ripresa.